HCDC4 - 4 Door Controller

• Supports 4 card readers

• 65,000 Cardholder Capacity on board.

• CCTV Integration.

• Graphical Maps

• High Security Pin # and Prox Combination.

• Unlimited Site Codes.

• 255 Access Privilege Groups.

• 200 Programmable Time Zones with 7 days and 1 holiday schedule each.

• 32 Programmable Holidays.

• 2,000 Event On Board Storage.

• Timed Anti-Pass Back, with individual, back to back or panel level Anti-Pass Back.

• Adjustable Unlock, Anti-Pass Back, and Held Open timers.

• On Board Power Supply for panel and readers.

• Battery Back-Up Circuitry.

• 4 Exit Button Inputs, 4 Door Contact Inputs, 4 Door Lock Outputs,

• 4 Auxiliary Outputs Controlled by Door Alarms, Card Shunting or Time Zones.

• Battery back up Circuitry.

• On board firmware clock.

• Power Requirements: 12VAC @ 40VA transformer.

• Option Stand By battery 12VDC 7.0Ah.

• Relays are Form C contact rated at 10A 125VAC.

• On board LED to indicate communications, Active Relays, AC source, as well as state of inputs.

 The Door Controller is a stand-alone unit.  Each panel has a unique address indicated on the PLCC chip in the center of the board. Once information is downloaded to the panel via the Protector software it will run independent of the P.C. Software.

HCDC4

HCDC2 - 2 Door Controller

• Supports 2 card readers .

• 2 Exit Button Inputs, 2 Door Contact Inputs, 2 Door Lock Outputs,

• 2 Auxiliary Outputs Controlled by Door Alarms, Card Shunting or Time Zones.

• All specifications are the same as the 4 door controller. Please see above.

HCEC8 - 8 Floor Elevator Controller

• Floor control

• Battery back up Circuitry

• On board firmware clock

• 65,000 user on board storage

• 2000 event on board storage

• Power Requirements: 12VAC @ 40VA transformer

• Option Stand By battery 12VDC 7.0Ah

• Relays are Form C contact rated at 10A 125VAC

• On board LED to indicate communications, Active Relays, AC source, as well as the state of the inputs.

The Elevator Controller is a stand-alone unit similar to our door controllers. Each panel has a unique address indicated on the PLCC chip in the center of the board.

• Additional 8 Floor control
• Connects to HCEC8 to provide an additional 8 floor control

HCSIO8 - Smart Input / Output Controller

• 8 Output control.

• 8 Unsupervised Input Control.

• Battery back up Circuitry.

• On board firmware clock.

• 2000 event on board storage.

• Power Requirements: 12VAC @ 40VA transformer.

• Option Stand By battery 12VDC 7.0Ah.

• Relays are Form C contact rated at 10A 125VAC.

• On board LED to indicate communications, Active Relays, AC source, as well as the state of the inputs.

The Smart I/O8 is a stand-alone unit similar to our door controllers. Each I/O Panel has a unique address indicated on PLCC chip in the center of the board. Inputs are programmed to arm according to an assigned time zone. Outputs can be programmed to activate according to an assigned time zone or to follow input for buzzer activation, etc. This Panel operates fully independent of the server or other panels on the network.

This Converter sits at the Server Software and connects to the PC via USB port and to the panels via cat5 cable.  The bus length can be up to 4000 feet with 32 controllers connected (daisy chain) anywhere along the bus.

This Converter allows you to connect your panels to connect to the server via TCPIP network.

You attach the device to a network port and wire the other end using Cat5  cable to the Door/elevator/IO controllers.  The bus length can be up to 4000 feet with 32 controllers connected (daisy chain) anywhere along the bus.

The server will then communicate via nic card to the HC-TCPIP and in turn to the controllers.

You can have up to 90 HC-TCPIP converters configured on your system.